3. Scanning & measuring rooms (LiDAR & AR) Each room is measured one at a time and automatically joins onto your floor plan .   Tips for a clean scan Close internal doors and turn on lights: Open doors can cause LiDAR to merge two rooms into one Ignore furniture: Sofas, tables, and kitchen units are automatically filtered out—only walls, doors, windows, and radiators are sent to Heatpunk Keep the phone held up between rooms: Moving with the camera upright helps the app track your position so the next room snaps neatly beside the previous one Method A: Scanning with LiDAR Stand close to a wall, point the phone at it, and tap the round blue button at the bottom . Walk slowly around the perimeter (roughly one step per second), sweeping the camera from floor to ceiling across every wall, door, and window . Mark radiators (optional): Tap directly on any radiator on your screen while scanning to place a marker on the nearest wall . Once you have scanned all walls (and at least 3 walls are detected), tap the round blue button again to finish and open the Room Steps . Warning: Tapping X at the top left immediately ends the current scan without asking for confirmation, and the room you are scanning will not be saved . Method B: Measuring with AR Measure Move your phone slowly over the floor until the dotted grid appears . Aim the centre ring at a floor corner and tap Corner . Repeat around the room, then aim back at the first corner and tap Corner again to close the room . Set Ceiling Height: Switch to the Height tab, aim where a wall meets the ceiling above a corner, and tap Set (or tap Same as last room ) . Add Doors, Windows & Radiators: Use the Door , Window , and Radiator tabs at the bottom to aim and tap opposite corners or edges for each opening or radiator . Tap Done at the top right (use Undo at the top if you misplace a point) . Moving between rooms & troubleshooting Next room or floor: After completing a room's steps, tap Next Room to keep scanning, or tap More > Next Floor when a floor is finished Rescan or add a missed room: Tap ... > Rescan Room or ... > Add a Missed Room ​ Expand the sections below for information on issues while scanning What if the phone loses its place during a scan? A phone call, screen lock, or switching to another app can cause the phone to lose track of its position . Your previously completed rooms remain saved, though the room you were actively scanning must be measured again . Find your place: The screen displays a photo of where your last scan finished . Walk back there and point the camera at the walls of a room you already scanned until the phone buzzes and Scan This Room reappears . Or tap Place by Hand : If the phone cannot re-lock onto a previous room, tap Place by Hand at the bottom and scan the room as normal . Drag the room into place: After scanning, the floor plan opens so you can drag the room into position (it snaps automatically to surrounding walls) . Use Turn to rotate it, or Line Up Door to align a shared doorway, then tap Place at the top right . Common messages while scanning or measuring LiDAR Scan messages: "Your phone is hot. Give it a minute to cool down.": Stop between rooms for a minute to let the device cool down, then carry on "The phone is low on memory. Finish this room soon.": Stop the current scan soon so the room saves properly "This room is taking a while.": Stop here and scan the remainder of the space as a separate room "That scan is of a room already on this floor.": Walk into the next unmeasured room before starting the scan "The scan stopped." / "The phone lost its place." / "This scan got too big.": Your previously completed rooms are saved—scan the current room again AR Measure messages: "Move your phone slowly over the floor": The app has not detected the floor plane yet—keep moving the camera slowly "Get closer / Aim at the floor": Move nearer to the corner and angle the camera lower "More light, or aim at something with a pattern": Turn on more lights—plain, shiny floors are difficult for the camera to track "That wall would cross another": The corner was placed in the wrong spot—tap Undo and try again "Point back at the last corner you placed": The phone lost tracking—aim back at the previous corner to re-lock ​ Still Need Help? Contact Support:  If you've got further questions, get in touch with our support team at  help@heatpunk.co.uk  (UK) or  help@heatpunk.ie  (IE).  If you are experiencing a bug, to help us look into your issue faster, please include the email address of your account, the name of the project and screenshots of any unexpected behaviour.