3. Scanning & measuring rooms (LiDAR & AR)
Each room is measured one at a time and automatically joins onto your floor plan.
Tips for a clean scan
-
Close internal doors and turn on lights: Open doors can cause LiDAR to merge two rooms into one
- Ignore furniture: Sofas, tables, and kitchen units are automatically filtered out—only walls, doors, windows, and radiators are sent to Heatpunk
- Keep the phone held up between rooms: Moving with the camera upright helps the app track your position so the next room snaps neatly beside the previous one
Method A: Scanning with LiDAR
-
Stand close to a wall, point the phone at it, and tap the
round blue buttonat the bottom. - Walk slowly around the perimeter (roughly one step per second), sweeping the camera from floor to ceiling across every wall, door, and window.
- Mark radiators (optional): Tap directly on any radiator on your screen while scanning to place a marker on the nearest wall.
- Once you have scanned all walls (and at least 3 walls are detected), tap the
round blue buttonagain to finish and open the Room Steps.
Warning: Tapping X at the top left immediately ends the current scan without asking for confirmation, and the room you are scanning will not be saved.
Method B: Measuring with AR Measure
-
Move your phone slowly over the floor until the dotted grid appears.
- Aim the centre ring at a floor corner and tap
Corner. Repeat around the room, then aim back at the first corner and tapCorneragain to close the room. - Set Ceiling Height: Switch to the
Heighttab, aim where a wall meets the ceiling above a corner, and tapSet(or tapSame as last room). - Add Doors, Windows & Radiators: Use the
Door,Window, andRadiatortabs at the bottom to aim and tap opposite corners or edges for each opening or radiator. - Tap
Doneat the top right (useUndoat the top if you misplace a point).
Moving between rooms & troubleshooting
- Next room or floor: After completing a room's steps, tap
Next Roomto keep scanning, or tapMore>Next Floorwhen a floor is finished - Rescan or add a missed room: Tap
...>Rescan Roomor...>Add a Missed Room
Expand the sections below for information on issues while scanning
What if the phone loses its place during a scan?
A phone call, screen lock, or switching to another app can cause the phone to lose track of its position. Your previously completed rooms remain saved, though the room you were actively scanning must be measured again.
- Find your place: The screen displays a photo of where your last scan finished. Walk back there and point the camera at the walls of a room you already scanned until the phone buzzes and
Scan This Roomreappears. - Or tap
Place by Hand: If the phone cannot re-lock onto a previous room, tapPlace by Handat the bottom and scan the room as normal. - Drag the room into place: After scanning, the floor plan opens so you can drag the room into position (it snaps automatically to surrounding walls). Use
Turnto rotate it, orLine Up Doorto align a shared doorway, then tapPlaceat the top right.
Common messages while scanning or measuring
LiDAR Scan messages:
- "Your phone is hot. Give it a minute to cool down.": Stop between rooms for a minute to let the device cool down, then carry on
- "The phone is low on memory. Finish this room soon.": Stop the current scan soon so the room saves properly
- "This room is taking a while.": Stop here and scan the remainder of the space as a separate room
- "That scan is of a room already on this floor.": Walk into the next unmeasured room before starting the scan
- "The scan stopped." / "The phone lost its place." / "This scan got too big.": Your previously completed rooms are saved—scan the current room again
AR Measure messages:
- "Move your phone slowly over the floor": The app has not detected the floor plane yet—keep moving the camera slowly
- "Get closer / Aim at the floor": Move nearer to the corner and angle the camera lower
- "More light, or aim at something with a pattern": Turn on more lights—plain, shiny floors are difficult for the camera to track
- "That wall would cross another": The corner was placed in the wrong spot—tap
Undoand try again - "Point back at the last corner you placed": The phone lost tracking—aim back at the previous corner to re-lock
Still Need Help? / Want to know more?
Contact Support: If you've got further questions, get in touch with our support team at help@heatpunk.co.uk (UK) or help@heatpunk.ie (IE). If you are experiencing a bug, to help us look into your issue faster, please include the email address of your account, the name of the project and screenshots of any unexpected behaviour.